Evidence used
- No CISA KEV confirmation is currently recorded.
- Exploitation requires an existing local or physical foothold with privileges.
- EPSS is 0.14% for the current model date.
BlackTreeCVE IntelligenceFull vulnerability report · 2026
CVE-2026-10674High confidence
DoS (hard fault) in NXP LPUART driver: unsupported runtime UART config leaves clocks disabled
zephyrproject · zephyr
Official source article: GitHub GHSA-MW68-R353-M3VF ↗. Check the applicable product and release in the original source.
5.5MediumCVSS 3.1
Scheduled
Patch availableMedium technical severity with no CISA KEV confirmation; remediate through the normal risk-based patch cycle unless local exposure raises the priority.
R
Open reassessment dashboard →Operational reassessment
Published severity in operational context
Published severityMedium→Operational priority:Low, lowered one band.downgradedsince 22 Jul 2026
Compensating controls
- Validate the affected product branch and deploy the verified fixed release.
- Restrict local access and enforce least privilege on affected hosts.
- Monitor vendor guidance and exploitation sources for a material change.
Verification
- Confirm that the asset runs zephyrproject zephyr and falls inside the recorded affected range.
- Verify the installed build against the product-specific fixed version after deployment.
- Validate exposure, authentication requirements and compensating controls in the actual environment.
- Reopen this reassessment when CVSS, KEV, EPSS, exploit evidence or remediation changes.
Medium technical severity with no CISA KEV confirmation; remediate through the normal risk-based patch cycle unless local exposure raises the priority.
Patch available01
What, why and how
The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before the clock is re-enabled. As a result, a uart_configure() request with an unsupported configuration left the LPUART in a clock-disabled state; any subsequent access to LPUART registers (poll_out/poll_in, interrupt handling, or a later reconfigure) faults on the gated peripheral and escalates to a hard fault, crashing the system. uart_configure() is a Zephyr syscall whose verifier (z_vrfy_uart_configure) only checks that cfg is readable user memory and forwards the caller-supplied configuration unchanged, so an unprivileged userspace thread with access to an LPUART device can deterministically trigger the fault, a persistent system-wide denial of service. Introduced in v2.5.0 and present in all subsequent releases until this fix, which removes the LPUART_Deinit() call and instead only disables the transmitter/receiver, leaving the clock running.
What
The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before the clock is re-enabled. As a result, a uart_configure() request with an unsupported configuration left the LPUART in a clock-disabled state; any subsequent access to LPUART registers (poll_out/poll_in, interrupt handling, or a later reconfigure) faults on the gated peripheral and escalates to a hard fault, crashing the system. uart_configure() is a Zephyr syscall whose verifier (z_vrfy_uart_configure) only checks that cfg is readable user memory and forwards the caller-supplied configuration unchanged, so an unprivileged userspace thread with access to an LPUART device can deterministically trigger the fault, a persistent system-wide denial of service. Introduced in v2.5.0 and present in all subsequent releases until this fix, which removes the LPUART_Deinit() call and instead only disables the transmitter/receiver, leaving the clock running.
Why
The product contains an assert() or similar statement that can be triggered by an attacker, which leads to an application exit or other behavior that is more severe than necessary.
How
An attacker operating through local access may attempt exploitation with low privileges. If successful, the issue may disrupt the affected service.
What
The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before the clock is re-enabled. As a result, a uart_configure() request with an unsupported configuration left the LPUART in a clock-disabled state; any subsequent access to LPUART registers (poll_out/poll_in, interrupt handling, or a later reconfigure) faults on the gated peripheral and escalates to a hard fault, crashing the system. uart_configure() is a Zephyr syscall whose verifier (z_vrfy_uart_configure) only checks that cfg is readable user memory and forwards the caller-supplied configuration unchanged, so an unprivileged userspace thread with access to an LPUART device can deterministically trigger the fault, a persistent system-wide denial of service. Introduced in v2.5.0 and present in all subsequent releases until this fix, which removes the LPUART_Deinit() call and instead only disables the transmitter/receiver, leaving the clock running.
Why
The product contains an assert() or similar statement that can be triggered by an attacker, which leads to an application exit or other behavior that is more severe than necessary.
How
An attacker operating through local access may attempt exploitation with low privileges. If successful, the issue may disrupt the affected service.
02
Exploit reality and attack path
CVSS severity, EPSS forecast probability, public exploit material and CISA-confirmed exploitation are separate signals.
Observed exploitation No confirmed evidence
?
Confirmed exploitation and public exploit material are separate signals. Attacks can occur without public proof-of-concept or exploit code.No CISA KEV match was present at the last successful refresh. This means no confirmation from that source, not proof of no exploitation.
Public PoC / exploit material None recorded
?
Confirmed exploitation and public exploit material are separate signals. Attacks can occur without public proof-of-concept or exploit code.No exploit-tagged reference or CISA SSVC proof-of-concept state is currently recorded. Research may still exist outside the structured feeds.
- Likely attack path
- local access → Reachable Assertion → disrupt the affected service
- Attack surface
- Local
- Privileges required
- Low: a basic authenticated account is required
- User interaction
- None
- Attack complexity
- Low: no specialised conditions are recorded
- Security boundary
- Unchanged: impact remains within the vulnerable component's security authority
- Weakness
?
CWE means Common Weakness Enumeration: a standard category for the underlying weakness. - CWE-617 ↗
CWE-617: Reachable Assertion. The product contains an assert() or similar statement that can be triggered by an attacker, which leads to an application exit or other behavior that is more severe than necessary.
- CVSS vector
?
CVSS means Common Vulnerability Scoring System. The vector records the metric values used to calculate technical severity. CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:HCommon Vulnerability Scoring System 3.1: the compact vector below is decoded into plain language.
AVLocalAttack vector: The attacker needs local access to the vulnerable system.ACLowAttack complexity: No specialised conditions are required beyond attacker-controlled input.PRLowPrivileges required: The attacker needs basic user-level privileges.UINoneUser interaction: No action by another user is required.SUnchangedScope: The security impact remains within the vulnerable component's authority.CNoneConfidentiality impact: No direct loss is represented by this metric.INoneIntegrity impact: No direct loss is represented by this metric.AHighAvailability impact: A successful attack can cause a major loss.- Post-exploitation / living off the land
- The issue can support a local privilege or sandbox boundary transition; normal system utilities may then be available in the gained context.
03
Patch and workaround
Operational remediation based on structured source evidence.
- Status
?
Patch availability is based on structured fixed-version fields and authoritative update references. If no fix is verified, check the vendor advisory before making a change. - Patch available
- Affected
- zephyr: 3.7.0 < 4.5.0
- Action
- Review the linked authoritative reference and apply the recorded fixed release appropriate to the affected product branch.
- Workaround
- No verified workaround is recorded. Limit untrusted access and use least privilege until authoritative guidance is available.
04
Evidence and provenance
Published 21 Jul 2026 · Last source change 22 Jul 2026, 19:37 UTC · CWE-617 · Reachable Assertion
CVE recordCVE.org · 5.2
CVSS sourceCNA
EPSS source FIRST · tracked since 2026-08-14
?
The date BlackTree first stored a score for this CVE from the daily FIRST EPSS feed.European sourceENISA EUVD · EUVD-2026-46444
Product sourceCNA
Remediation sourceCVE/CNA references
CWE sourceCNA
NVD statusNVD enriched
Core structured fields are present and their contributing authorities are shown above.
Material change intelligence
View recent updates ↗What changed after publication
No material field changes have been recorded since change tracking began. Routine source refreshes and cosmetic edits are intentionally excluded.
CVE published
Fixed release or patch reference recorded
Technical terms and abbreviations used in this report
- CVE
- Common Vulnerabilities and Exposures: the public identifier for one disclosed vulnerability.
- CVSS
- Common Vulnerability Scoring System: a technical severity framework; it is not patching priority by itself.
- EPSS
- Exploit Prediction Scoring System: FIRST's estimate of the probability that exploitation activity will be observed in the next 30 days; it is a forecast, not confirmation.
- CWE
- Common Weakness Enumeration: the standard category describing the underlying software or hardware weakness.
- CNA
- CVE Numbering Authority: an organisation authorised to assign and publish CVE records.
- CISA ADP
- Cybersecurity and Infrastructure Security Agency Authorized Data Publisher: structured enrichment added to a CVE record.
- NVD
- National Vulnerability Database: NIST's enrichment service for CVE records.
- CERT / CSIRT
- A computer security incident response team that publishes warnings or coordinates incident response.
- PoC
- Proof of concept: public material that demonstrates or helps reproduce exploitation.
- CSAF
- Common Security Advisory Framework: a machine-readable format for security advisories.
- LoTL
- Living off the land: abuse of legitimate tools or system functions during an attack.